How To Remove Headlight Assembly Ford F250

**The StandardAmericanDad.com is a participant in the Amazon Services LLC Associates Plan, an chapter advertising programme designed to provide a means for sites to earn advertisement fees past advertizing and linking to amazon.com. As an Amazon Associate I earn from qualifying purchases.**

• 2011 to 2022 F250 LED Headlight Bulb Replacement Instructions
  • Required Tools to consummate 2022 to 2022 F250 LED Headlight Bulb Replacement Instructions
  • Step one: F250 Grill Removal
  • Step 2: F250 Headlight Unit Removal
  • Step three: Replace the Bulb with LED
  • Step iv: Reassemble
  • Summary of 2022 to 2022 F250 LED Headlight Replacement Instructions:

2011 to 2022 F250 LED Headlight Bulb Replacement Instructions

My F250 Headlight Bulb Replacement instructions come from offset hand experience installing new LED bulbs in my truck. After replacing the headlights on my wife'south 2022 Hyundai Santa Fe I quickly realized that Halogens just wouldn't cutting it in my truck anymore. Since hers required a bit of modification I went straight to my truck to see how achievable this project would be.

I bought this truck back in the Leap and had simply looked under the hood prior to purchasing information technology. As shortly every bit the hood went up I remembered how limited space is in the 6.7 Powerstroke with dual batteries. I couldn't even see the dorsum of the headlight bulb much less get my arm down there to remove and supersede it. So back to the drawing board I went. After consulting a couple of videos and wasting more time listening to rambling than I spent actually replacing them I decided a more elementary tutorial was needed for F250 LED Headlight Seedling Replacement Instructions and LED Conversion (2011-2015).

First, I looked up the model number to fit my truck and realized the LED Loftier/Low Beam philharmonic for my 2022 F250 was significantly higher than the Low Axle Bulb for her car. Next, I lookout listed them on Amazon and waited until Honey sent me an email notifying that they were discounted $viii on Amazon Prime Twenty-four hours (Never heard of the disbelieve code app Dearest? Check out my review here!) . After double checking the model number for my truck I placed the guild. I received them a few days later and waited for a day below 95 F so that I could comfortably climb under the hood to install them.

Required Tools to complete 2022 to 2022 F250 LED Headlight Bulb Replacement Instructions

+ H13 LED Replacement Bulbs (something like Auxbeam)
+ 10 mm Socket
+ 1/4 Drive Ratchet
+ Minimum of 6″ 1/four Bulldoze Extension
+ 6″ + Flat Screwdriver

Pace one: F250 Grill Removal

1a) Information technology sounds daunting merely it is surprisingly piece of cake. First, make note of the location of the washers by observing the indention the teeth make, with a silver marking pen, or with a strip of tape. This will help make sure the grill is lined upwards properly when the hood closes later. And so remove the 4 – 10mm bolts on top. Mine did not have a Push button Rivet on the right side but yours might.

1b) After the four bolts are removed the top of the grill can be carefully tilted abroad from the truck. Reach behind it and use the Flat Screwdriver to press down on each of the 5 metal clips at the base. These release rather hands after the screwdriver is inserted through the hole on top. Afterward the clips have all been released the grill can be carefully removed from the truck and sat to the side.

4 Bolts for Grill Removal

Xanthous is Bolt Locations for reference. Red is Clip Locations

Back of grill bolt holes (4x) and metal clips (5x)

Step 2: F250 Headlight Unit of measurement Removal

2a) Afterwards the grill has been removed yous proceeds access to the two eye bolts (10mm) that hold the headlight unit in place. Remove these along with the i bolt (10mm) on top. My truck did non have a bottom bolt but I take seen videos of a few (aftermarket headlights) that did accept a bottom commodities between the headlight and bumper.

• 

  2 – 10mm bolts on the side of the headlight housing

• 

  1 – 10mm commodities on top of the headlight housing.

2b) When all bolts have been removed pull the headlight direct out away from the cab. Information technology may hang slightly equally the plastic tabs in the back snap out of the alignment slot. See the Image below.

Step three: Replace the Bulb with LED

3a) When the electrical socket becomes accessible go ahead and release it while the bulb is still locked into the housing. Practise this by pushing on the clip while pulling on the plug. Information technology's much more hard to separate after taking the bulb out of the housing.

3b) Later the electrical connectedness is separated, twist the bulb counter clockwise 1/three of a plough, and remove the seedling. My factory bulb left the O-band behind and prevented my new bulb from locking into place.

• 

  H13 LED with cord

• 

  H13 Plug

• 

  Built in cooling fan

3c) Remove the one-time O-band and use the 1 that comes with the Auxbeam LED H13 bulbs for an easy fit. Later on its locked into place, connect the socket to the cord and test the bulbs.

• 

  3b) empty socket with old O-band in identify

• 

  3c) Remove old o-ring and lock in new bulb

Step 4: Reassemble

4a) Finally, later on testing the high/low beam and confirm both are working begin reassembly by placing the 3 or iv 10mm headlight bolts back into place making certain the peak commodities is in the same location in the slot.

4b) Carefully identify the bottom of the grill in line with the 5 metal clip slots. Tilt the top up and gently press on the bottom of the grill to snap the clips into identify one at a time. Subsequently that, give information technology a little pull to brand sure all are secure.

4c) When the lesser is secure tilt the top back into place and reinstall the 4 bolts and washers. Ensure yous line up the factory washer marks perfectly or there volition be an uneven gap between the grill and hood.

4d) Look until dark and give the truck a little test bulldoze to appreciate your newly upgraded LED Headlights.

Images beneath are unedited and taken with my iPhone in the aforementioned section of road.

Before (Halogen)

Subsequently (AuxBeam F-S2 Serial LED)

Summary of 2022 to 2022 F250 LED Headlight Replacement Instructions:

1. Gather the tools needed. (x mm socket with extension and a long flat caput screwdriver)
2. Remove the Grill. Mark Bolt locations and remove 4 bolts from the top of the grill, tilt out, and utilise the flat head to release the five metal clips on the bottom.
3. Remove three or iv (if bottom bolt exists) 10 mm bolts belongings headlight housing in position.
4. Pull headlight housing directly out.
5. Disconnect bulb socket.
6. Twist existing seedling 1/3 counterclockwise and remove o-ring.
7. Install new LED Bulb, lock into identify with one/3 plough clockwise.
8. Plug in the electric socket and test Hullo and Depression beams.
9. Reinstall headlight unit of measurement.
10. Line up grill, press clips (5) into place, line up commodities holes (4) and tighten.
11. Enjoy your new vivid white low-cal!

If y'all are looking for a budget friendly LED solution for your vehicle check out Auxbeam.com or observe Auxbeam on Amazon. I chose this brand for my wife's 2022 Hyundai Santa Iron with enclosed headlights considering of the price point, agile fan, and 2 twelvemonth warranty. Considering I'1000 a creature of addiction I went with the same model for the truck. If you try other models go out some feedback!

***Save ten% on all orders over $50 at AuxBeam***
***Extra fifteen% Off Outdoor Hunting Photographic camera***

Source: https://www.standardamericandad.com/f250-led-headlight-replacement-instructions/

Share this post